Loxone 1-Wire Extension
The 1-Wire Extension allows the integration of 1-Wire sensors to your system Loxone. The sensors are inexpensive and easy to install, ideal if you are installing many sensors.
- 1-Wire interface (5V output max. 50mA)
- Connection of up to 20 sensors or one iButton reader
- Transmission speed 16.3 kbit/s
- Unlimited iButton
- Power supply 24VDC
- Connection to Loxone Link
- ETL Listed
The 1-Wire Extension allows the integration of 1-Wire sensors to your system Loxone. The 1-Wire Extension is ideal for installations where many sensors are required. The reliable sensors are inexpensive and easy to install. With the Miniserver connected, multiple sensors can be connected to the 1-Wire Extension.
Recommended Topology
Bus topology without branches
Bus technology without branches is best suited for cabling. This offers a range of up to 1,148 ft (350m).
Bus topology with branches
With branches, a similar result can be achieved. However, the maximum range is up to 984 ft (300m).
More topologies
Bus topology with long branches
Bus topology with long branches is recommended to an extent, allowing cabling of up to 328 ft (100m).
Star topology
Star topology is only recommended for smaller installations, allowing cabling of up to 328 ft (100m) .
Technical Specifications
- Interface: Loxone Link connection with Miniserver or Miniserver Go
- Power Consumption: max. 110mW
- 1-wire Inputs: max 20 sensors, with max 50mA or 1 iButton Key Reader
- Max wire length: 100 to 300m
Downloads
Product Datasheet
Product insert
Declaration of conformity
Declaration of conformity CZ
ETL Certificate
Shipped in the Box
- 1 x 1-Wire Extension
- 1 x Wiring diagram and Quick Start Guide
If using the Miniserver
Components List
- 1 x Miniserver is required
- 1 x Network Switch or Modem required
- 1 x 24VDC Power supply required
Wire List
- 1 x Cat5 or better, network Cable to connect the Miniserver to your network or computer to program the system
- 1 x 18 AWG to 23 AWG pair (solid core preferred) to transfer power from Power supply to Miniserver
- 1 x 18 AWG to 23 AWG pair (solid core preferred) to transfer power from the Power supply or Miniserver to the Extension
- 1 x 18 AWG to 23 AWG twisted pair (solid core and shielded preferable) to connect the Miniserver’s Loxone Link to the Extension
If using the Miniserver Go
Components List
- 1 x Miniserver Go is required
- 1 x Network Switch or Modem Required
- 1 x 24VDC Power supply required
Wire List
- 1 x Cat5 or better, network Cable to connect the Miniserver Go to your network or computer to program the system
- 1 x 18AWG to 23 AWG wire (solid core preferred) to ground from Power supply negative to the Miniserver Go
- 1 x 18 AWG to 23 AWG pair (solid core preferred) to transfer power from Power supply to Extension
- 1 x 18 AWG to 23 AWG twisted pair (solid core and shielded preferable) to connect the Miniserver Go’s Loxone Link to the Extension
Installation Diagram
Graphic or Wiring diagram of Loxone 1-Wire Extension installed. In the diagram you see the 1-Wire Extension installed to the right of the Miniserver Gen 2. Both are powered by a DIN rail 24VDC power supply. The Miniserver, the power supply and the 1-Wire Extension are installed on a DIN rail which is attached inside the panel. To the left of the Miniserver is a DIN rail mounted 24VDC power supply. The power supply has a 2-conductor wire connected to the Miniserver to provide 24VDC power. From the top of the Miniserver is also a line indicating its attachment to the LAN via a network switch which is located outside and on the top of the panel. The 1-Wire Extension is also getting a blue cable from the Miniserver which indicates a Loxone Link Communication.