window.dataLayer = window.dataLayer || []; function gtag(){dataLayer.push(arguments);} gtag('js', new Date()); gtag('config', 'G-ZJMPYD9EC7');
Home » Shop » Loxone » Extensions » Loxone Modbus Extension

Loxone Modbus Extension

USD $289.12

Item no.: 100124

The Modbus Extension expands your Loxone system and allows:

  • the reading of various meters such as gas, electricity and energy
  • collection of statistical data from electricity, gas, water and energy meters
  • the recording of consumption data for intelligent energy management
  • ETL Listed

The Modbus interface for your building automation project

Whether in a smart home or any commercial building, the Modbus Extension can control all Modbus-based meters. Collect statistical data from electricity, gas, water and energy meters and record consumption data for intelligent energy management. The Miniserver sends commands to a device with a Modbus interface via the Modbus Extension.

Flexible expansion

Up to 32 Modbus devices can be controlled per Modbus Extension. Up to 20 extensions can be connected to the Miniserver without affecting the performance of the system. You can also use several Modbus Extensions on an installation.

Simple configuration

With the free Loxone Config software, you can get the Modbus Extension set up and ready to start sending and receiving commands in no time.

Technical Specifications

  • Interface: Loxone Link connection with Miniserver or Miniserver Go
  • Power Consumption: max 60mW
  • Modbus RTU interface: max 32 devices or 253 sensors
  • Wire length: 1200m wire length
  • Adjustable baud rate & parity
  • Data types: 16 & 32bit
  • Min Polling cycle: 5s

Downloads

Shipped in the Box

  • 1 x Modbus Extension
  • 1 x Wiring diagram and Quick Start Guide

If using the Miniserver

Components List

    • 1 x Miniserver is required
    • 1 x Network Switch or Modem required
    • 1 x 24VDC Power supply required

Wire List

    • 1 x Cat5 or better, network Cable to connect the Miniserver to your network or computer to program the system
    • 1 x 18 AWG to 23 AWG pair (solid core preferred) to transfer power from Power supply to Miniserver
    • 1 x 18 AWG to 23 AWG pair (solid core preferred) to transfer power from the Power supply or Miniserver to the Extension
    • 1 x 18 AWG to 23 AWG twisted pair (solid core and shielded preferable) to connect the Miniserver’s Loxone Link to the Extension

If using the Miniserver Go

Components List

    • 1 x Miniserver Go is required
    • 1 x Network Switch or Modem Required
    • 1 x 24VDC Power supply required

Wire List

    • 1 x Cat5 or better, network Cable to connect the Miniserver Go to your network or computer to program the system
    • 1 x 18AWG to 23 AWG wire (solid core preferred) to ground from Power supply negative to the Miniserver Go
    • 1 x 18 AWG to 23 AWG pair (solid core preferred) to transfer power from Power supply to Extension
    • 1 x 18 AWG to 23 AWG twisted pair (solid core and shielded preferable) to connect the Miniserver Go’s Loxone Link to the Extension

Installation Diagram

Graphic or Wiring diagram of Loxone Modbus Extension installed. In the diagram you see the Modbus Extension installed to the left of the Miniserver Gen 2 (Miniserver). Both are powered by a din Rail 24VDC power supply. The Miniserver, the Power supply and the Modbus extension are installed on a Din Rail which is attached inside the panel. To the left of the Miniserver is a Din Rail mounted 24VDC power supply. The power supply has a 2-conductor wire connected to the Miniserver to provide 24VDC power. From the top of the Miniserver is also a line indicating its attachment to the LAN via a network switch which is located outside and on the top of the panel. The Modbus extension also getting a blue cable from the Miniserver which indicates a Loxone Link Communication.

Go to Top